thejollysinker Posted August 20, 2023 Share Posted August 20, 2023 (edited) One of my caps is starting to rot on the metal bit that snaps onto the plug’s threaded end. Question: can I unscrew it from the HT lead and replace it or am I looking at replacing the coil pack as a whole? The engine is a 2001 Yamaha F60. I had a fiddle with it yesterday and it gave me the impression that I could unscrew it and replace. meanwhile I have a new fuel filter that doesn’t fit my housing that I’ll post if anyone can use it…. Photo with part number here 👇 Edited August 20, 2023 by thejollysinker Quote Link to comment Share on other sites More sharing options...
Andy135 Posted August 20, 2023 Share Posted August 20, 2023 I don't know about your engine specifically but I'd be surprised if the leads weren't replaceable. Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted August 20, 2023 Author Share Posted August 20, 2023 23 minutes ago, Andy135 said: I don't know about your engine specifically but I'd be surprised if the leads weren't replaceable. They look like they are but, I happened upon another forum where one member was insistent that if you unscrewed the lead from the coil pack there was no going back…. Atm I have some fine s/s wire wrapped around the threaded part of the plug which isn’t ideal but ‘works’. Andy135 1 Quote Link to comment Share on other sites More sharing options...
Andy135 Posted August 20, 2023 Share Posted August 20, 2023 2 hours ago, thejollysinker said: They look like they are but, I happened upon another forum where one member was insistent that if you unscrewed the lead from the coil pack there was no going back…. Atm I have some fine s/s wire wrapped around the threaded part of the plug which isn’t ideal but ‘works’. He may be right - I'm looking at it from a car engine perspective but I can see why a marine engine manufacturer would want to seal the joint. thejollysinker 1 Quote Link to comment Share on other sites More sharing options...
Gordmac Posted August 21, 2023 Share Posted August 21, 2023 Make it waterproof? Sell more expensive parts? If you can find a parts catalogue, if the lead is available separately it will have a part number. thejollysinker 1 Quote Link to comment Share on other sites More sharing options...
mick Posted August 21, 2023 Share Posted August 21, 2023 Just googled it and the genuine plug cap is about £60 and screws onto lead. Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted August 21, 2023 Author Share Posted August 21, 2023 Thanks for the info mate. 60 smackers for a spark plug cap 😳 I’ll get 4 and some spares 🤣 mick and daio web 1 1 Quote Link to comment Share on other sites More sharing options...
suzook12 Posted August 22, 2023 Share Posted August 22, 2023 looked on boats.net, full lead and plug is replaceable. Now, I would imagine, if you slide the rubber boot off, there will be a plastic spring clip in there that holds the lead in on the spike. As for the caps themselves, just make sure whether or not they are resistor caps. Resistor caps are usually 5K ohms.... No reason why you couldn't use whatever plug cap you want. thejollysinker and MegaByte 1 1 Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted August 23, 2023 Author Share Posted August 23, 2023 12 hours ago, suzook12 said: looked on boats.net, full lead and plug is replaceable. Now, I would imagine, if you slide the rubber boot off, there will be a plastic spring clip in there that holds the lead in on the spike. As for the caps themselves, just make sure whether or not they are resistor caps. Resistor caps are usually 5K ohms.... No reason why you couldn't use whatever plug cap you want. That’s really helpful. Good to know I can’t break anything if I start pulling things apart 👍 I’ll give them a test with the meter to find out if they are resistor caps, didn’t know there was such a thing 🤷♂️ and I did wonder about using something else apart from OEM products which seem overly expensive for what they are. Thanks for your help 🙂 Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted September 17, 2023 Author Share Posted September 17, 2023 On 8/22/2023 at 6:46 PM, suzook12 said: looked on boats.net, full lead and plug is replaceable. Now, I would imagine, if you slide the rubber boot off, there will be a plastic spring clip in there that holds the lead in on the spike. As for the caps themselves, just make sure whether or not they are resistor caps. Resistor caps are usually 5K ohms.... No reason why you couldn't use whatever plug cap you want. UPDATE: pulled the rubber caps off the coils to find that the leads are sealed in place with what looks like some kind of resin so no new leads are going to fitted. I had ordered some new HT lead wire and 5K Ohm Champion rubber caps (which didn't cost a lot) so will just fit the caps which should be enough to sort the problem out. Saintly Fish, mick and Andy135 3 Quote Link to comment Share on other sites More sharing options...
suzook12 Posted September 23, 2023 Share Posted September 23, 2023 On 9/17/2023 at 5:14 PM, thejollysinker said: UPDATE: pulled the rubber caps off the coils to find that the leads are sealed in place with what looks like some kind of resin so no new leads are going to fitted. I had ordered some new HT lead wire and 5K Ohm Champion rubber caps (which didn't cost a lot) so will just fit the caps which should be enough to sort the problem out. That's odd. Hopefully the caps will do the trick 👍 thejollysinker 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.