Popular Post thejollysinker Posted September 24, 2023 Popular Post Share Posted September 24, 2023 (edited) Took the opportunity to go out yesterday as there was a small weather window which couldn’t be ignored. Beautiful calm morning and with fresh anti fouling on the hull it was hammer down time to get over to the Ore Stone for a jigging session. 21kts achieved, got there nice and quick so thought I’d try ‘mackerel corner’ at Hope’s Nose first. 3 drifts, a suicidal tiny pollack and 2 joey macks later I headed off to Tucker Rock reef and was in straightaway with some nice sized fat mackerel 👌 I continued to do repeat drifts along the edge of the reef and bagged up with about 15kg of mackerel and scad with a solitary sardine in the mix. I really wanted a red gurnard for my species hunt group as I already had tubs and greys so fished hard on the bottom every drift and was overjoyed to get one after about an hour of trying 😅 I really wanted to anchor up on the northward flow at the back of the reef and foolishly decided to go for it knowing that the wind was going to get up a bit. Got some nice fresh baits down on 12lb class gear, 3 oz leads and away we go, dogfish🤣 It got rough very quickly and the yachties were now out in force using me as a bloody target🤷♂️ carried on and got a ratchet whizzing bite which gave me a hell of a fight. Took about ten minutes to get it up and wasn’t surprised to see a 20lb plus conger which I had to gaff as I was struggling to stand up let alone net the bugger 🤣 Another fresh bait sent down saw a lovely Huss of around 12lb come up, chuffed with that. Next bait saw a really gentle bite so I left it a couple of minutes then pulled into it only to get another epic battle which saw a 24lb conger come up (I weighed it best I could in the by now awful conditions). This is where my day went downhill. I could not for the life of me use the Alderney ring technique to retrieve my anchor…. every time I tried I lost sight of the rope, couldn’t keep direction in the snotty sea and completely lost confidence in what I was doing. I even went over the bloody thing once so engine off and tilt up….. no choice but to pull by hand which was like riding a bucking bronco and I very nearly decided to cut and run. The nose of my boat nearly went under at one point and I seriously questioned my sanity. Anyway, once it finally broke free I managed to get it up and stowed it through the front hatch. I made for quieter waters and then sorted it all out. Got back to the mooring with a sense of relief and was treated to the spectacle of about 10 mullet messing around under my tender alongside the boat in a foot or so of water and they were pretty big, 3 or 4 lbs apiece 👌 So for the first trip out on my own in 18 months it was probably the best trip I’ve had since I started boat fishing which was only tainted by the anchor incident. I’m here to tell the tale and that’s all that matters, lesson learnt 👍 8 species, mackerel, scad, sardine, pollack, red gurnard, dogfish, conger and Huss….. I very nearly landed a huge spider crab but he let go at the last minute 🤣 Edited September 24, 2023 by thejollysinker Josh, suzook12, GPSguru and 5 others 8 Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted September 24, 2023 Author Share Posted September 24, 2023 5 minutes ago, JonC said: Nice right up thanks, shame your day was blighted with them dogs. It was too windy here for fishing, I got out sailing on my cat yesterday but today was gusting hi 30mph I only included the dogs for you know who 🤣 Andy135 1 Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted September 24, 2023 Author Share Posted September 24, 2023 6 minutes ago, JonC said: I haven’t seen any on the last 4-5 trips out which is great. Hopefully they will stay gone all winter and give a chance for for the cod to find out baits. Hopefully 🤞 Quote Link to comment Share on other sites More sharing options...
RogB Posted September 24, 2023 Share Posted September 24, 2023 Sounds and looks like a fun day out, glad you made it back to post the photos and report! Andy135 and thejollysinker 1 1 Quote Link to comment Share on other sites More sharing options...
Andy135 Posted September 24, 2023 Share Posted September 24, 2023 Top dangling that man! @GPSguru did mention on Whatsapp that you were out. Glad to see you had a busy session. Alderney retrieval always used to give me a squeaky bum even in the best of conditions so I reckon you made the right call in snotty weather and single-handed. No prizes for trying to be a hero out there 👍 Good fish pics too. Shame you didn't get more dogs but I suppose you can't win 'em all. #somanydogfishsolittletime thejollysinker 1 Quote Link to comment Share on other sites More sharing options...
Saintly Fish Posted September 24, 2023 Share Posted September 24, 2023 Nice going. Sounds like an exciting day on the water. I have hand hauled an anchor in less than desirable conditions a few times and it's no fun. Even worse if you don't have any gloves on!! 😬 thejollysinker 1 Quote Link to comment Share on other sites More sharing options...
Dicky Posted September 24, 2023 Share Posted September 24, 2023 Great report, nice to see you got out thejollysinker 1 Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted September 24, 2023 Author Share Posted September 24, 2023 52 minutes ago, Andy135 said: Top dangling that man! @GPSguru did mention on Whatsapp that you were out. Glad to see you had a busy session. Alderney retrieval always used to give me a squeaky bum even in the best of conditions so I reckon you made the right call in snotty weather and single-handed. No prizes for trying to be a hero out there 👍 Good fish pics too. Shame you didn't get more dogs but I suppose you can't win 'em all. #somanydogfishsolittletime Nothing gets past Ian down there does it 🤣 mate, I was crapping it just a bit when them waves were sloshing over the bow. I was jammed in the hatch like a dried up marmite lid….legs were feeling it today 🤣 I only managed to land 2 doggies, thankfully 😅 I do try to dissuade them with rather large baits and hooks but it doesn’t always work 🤣🤣🤣 Andy135 and GPSguru 1 1 Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted September 24, 2023 Author Share Posted September 24, 2023 42 minutes ago, Saintly Fish said: Nice going. Sounds like an exciting day on the water. I have hand hauled an anchor in less than desirable conditions a few times and it's no fun. Even worse if you don't have any gloves on!! 😬 Gloves 🤔 Saintly Fish 1 Quote Link to comment Share on other sites More sharing options...
daio web Posted September 25, 2023 Share Posted September 25, 2023 great report buddy nice to read a report again well hopefully get a few now thejollysinker 1 Quote Link to comment Share on other sites More sharing options...
Popular Post GPSguru Posted September 25, 2023 Popular Post Share Posted September 25, 2023 (edited) On 9/24/2023 at 7:29 PM, thejollysinker said: This is where my day went downhill. I could not for the life of me use the Alderney ring technique to retrieve my anchor…. every time I tried I lost sight of the rope, couldn’t keep direction in the snotty sea and completely lost confidence in what I was doing. OK, I understand the issue, this may help. Once anchored, back off the warp until the buoy is about 30yards from the boat. When you are ready to recover, clear the deck on the same side as the helm (I assume yours is starboard). Move off at a 45 degree angle to the buoy and then watch the warp at the bow to maintain the angle, you will then be making a large arc around the buoy. The buoy will go under and the popup once the anchor has broken free. This is the important bit .......... now the anchor has broken free, steer slightly straighter and the warp will come along side the boat. KEEP THE POWER ON, lean over the side and grab the warp (it will be almost at gunnel height), with the power still on leave the helm and run back to the stern still holding the warp and put a quick turn around the stern gunnel cleat. Run back to the helm, and you can then watch the angle of the warp off the stern gunnel and the buoy. Open up with more throttle until the buoy is firmly being towed, then slow down to stationary and walk back to release the rope off the stern cleat. If you are not using a lazy line, then make a very low speed skid turn to point the bow at the buoy. Leave the engine on with the boat stationary and engine on idle, recover the warp and buoy. If you are using a lazy line, then just recover the warp and buoy from the stern, and then tie off the lazy line in its normal position. Regardless of how bad the sea is, by looping onto the stern gunnel cleat, you can always see the angle of the warp. If you don't use the stern cleat, then it is easy to lose sight of the warp and run over it. Also, you should always have your anchor set to trip, even with the slightest snag. Mine will trip about 1 in 5 times when recovering. Just replace the cable tie, and ready to go. Edited September 25, 2023 by GPSguru Josh, Geoff, thejollysinker and 2 others 2 1 1 1 Quote Link to comment Share on other sites More sharing options...
Saintly Fish Posted September 26, 2023 Share Posted September 26, 2023 6 hours ago, GPSguru said: Regardless of how bad the sea is, by looping onto the stern gunnel cleat, you can always see the angle of the warp. If you don't use the stern cleat, then it is easy to lose sight of the warp and run over it. I can't say I've ever had to do this Ian, but it's a dammed good idea! Quote Link to comment Share on other sites More sharing options...
Andy135 Posted September 26, 2023 Share Posted September 26, 2023 33 minutes ago, JonC said: I’m sure @GPSguru has got his technique down when he’s doing this but it reads like the kill cord needs to be detached while the operator is away from the helm with the engine engaged forward? Or am I looking at this from the wrong end of the telescope? I suppose it depends how long the boat is and how long the kill cord is, but in principle you make a fair point. Geoff and daio web 2 Quote Link to comment Share on other sites More sharing options...
GPSguru Posted September 26, 2023 Share Posted September 26, 2023 3 hours ago, JonC said: I’m sure @GPSguru has got his technique down when he’s doing this but it reads like the kill cord needs to be detached while the operator is away from the helm with the engine engaged forward? Or am I looking at this from the wrong end of the telescope? Yes, leave the kill cord off, however, If sea conditions dictate it should be worn, then just connect 2 together, as you should always have a spare on the boat. TBH, I often use 2 cords if I am on my own, to allow freedom of movement to the stern. daio web, Saintly Fish, Andy135 and 1 other 4 Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted September 26, 2023 Author Share Posted September 26, 2023 10 hours ago, GPSguru said: OK, I understand the issue, this may help. Once anchored, back off the warp until the buoy is about 30yards from the boat. When you are ready to recover, clear the deck on the same side as the helm (I assume yours is starboard). Move off at a 45 degree angle to the buoy and then watch the warp at the bow to maintain the angle, you will then be making a large arc around the buoy. The buoy will go under and the popup once the anchor has broken free. This is the important bit .......... now the anchor has broken free, steer slightly straighter and the warp will come along side the boat. KEEP THE POWER ON, lean over the side and grab the warp (it will be almost at gunnel height), with the power still on leave the helm and run back to the stern still holding the warp and put a quick turn around the stern gunnel cleat. Run back to the helm, and you can then watch the angle of the warp off the stern gunnel and the buoy. Open up with more throttle until the buoy is firmly being towed, then slow down to stationary and walk back to release the rope off the stern cleat. If you are not using a lazy line, then make a very low speed skid turn to point the bow at the buoy. Leave the engine on with the boat stationary and engine on idle, recover the warp and buoy. If you are using a lazy line, then just recover the warp and buoy from the stern, and then tie off the lazy line in its normal position. Regardless of how bad the sea is, by looping onto the stern gunnel cleat, you can always see the angle of the warp. If you don't use the stern cleat, then it is easy to lose sight of the warp and run over it. Also, you should always have your anchor set to trip, even with the slightest snag. Mine will trip about 1 in 5 times when recovering. Just replace the cable tie, and ready to go. Right, I now understand more what I'm doing wrong either through lack of research or reading articles that explain differently. The biggest single issue must be me not leaving enough space between the boat and the buoy! I'll try again next time to give this a try. When I have managed to successfully use this technique in the past I haven't had any issues but that was in different conditions. I have in the past thought about rigging up some more metalwork on the rear rails with a standoff arm to run the rope through so it will never be near the engine if you can picture it? I honestly think I'd struggle to cleat it off as the cleats are sunken into the top moulding which I don't think is a good design feature as it makes it more awkward to rope things off including the mooring ropes. The anchor is set to trip but this time it didn't (with the same cable tie configuration I've used before) so I'll change that to make it trip easier. For info. I use the port side to haul it and store some of the rode along with chain, anchor and buoy in a big flexi bucket while the rest of it runs atop to the anchor well. I have actually got a stainless tube attached to the end of the rode so in an emergency I could just dump the whole lot and retrieve later. Trouble with that is there would be 220m of rope behind the boat and I probably wouldn't even be able to see the buoy 🤣 Thanks for the advice Ian 😊 GPSguru and daio web 2 Quote Link to comment Share on other sites More sharing options...
GPSguru Posted September 26, 2023 Share Posted September 26, 2023 (edited) 3 hours ago, thejollysinker said: Right, I now understand more what I'm doing wrong either through lack of research or reading articles that explain differently. The biggest single issue must be me not leaving enough space between the boat and the buoy! I'll try again next time to give this a try. When I have managed to successfully use this technique in the past I haven't had any issues but that was in different conditions. I have in the past thought about rigging up some more metalwork on the rear rails with a standoff arm to run the rope through so it will never be near the engine if you can picture it? I honestly think I'd struggle to cleat it off as the cleats are sunken into the top moulding which I don't think is a good design feature as it makes it more awkward to rope things off including the mooring ropes. The anchor is set to trip but this time it didn't (with the same cable tie configuration I've used before) so I'll change that to make it trip easier. For info. I use the port side to haul it and store some of the rode along with chain, anchor and buoy in a big flexi bucket while the rest of it runs atop to the anchor well. I have actually got a stainless tube attached to the end of the rode so in an emergency I could just dump the whole lot and retrieve later. Trouble with that is there would be 220m of rope behind the boat and I probably wouldn't even be able to see the buoy 🤣 Thanks for the advice Ian 😊 Is your helm on the port side ? As you always should recover on the same side as the helm. With regard to the stern cleats, you can just take a single turn around anything on the stern as it is still the bow that is taking the strain. I take a single turn around the stern mooring cleat on the tube ! Yes, not leaving a good distance from bow to buoy is a common error. The closer it is, the smaller the arc that you tend to take, and therefore have less visibility and less control. Edited September 26, 2023 by GPSguru Quote Link to comment Share on other sites More sharing options...
Dicky Posted September 26, 2023 Share Posted September 26, 2023 I definitely wouldn't tie off to a stern cleat if you are a little unsure or not fully confident you have raised the anchor off the sea bed first. GPSguru is very experienced so he may be happy that way but i wouldn't advise it. The main factor has already been mentioned and that is to ensure your buoy is far enough in front of the boat at the start of the manoeuvre. We were taught to also raise the anchor on the other side to the helm on our RYA PBL2. Each to their own and confidence will play a big part in how you do it. GPSguru 1 Quote Link to comment Share on other sites More sharing options...
GPSguru Posted September 27, 2023 Share Posted September 27, 2023 3 hours ago, Dicky said: I definitely wouldn't tie off to a stern cleat if you are a little unsure or not fully confident you have raised the anchor off the sea bed first. No, we don't tie off to the stern cleat, we just take one turn around it, so pretty easy to slip it off if it turns pear shaped. Generally if the buoy has popped up then the anchor has broken free. Very often I just put the warp on the inside of the cleat, which is often good enough to see what you are doing, and to keep the warp away from the prop. I also carry a knife on my belt at all times and there is another in the stern pocket. Fortunately, we don't experience tides speed like you guys in the BC. Even on a raging spring, Gary would have only been in 2kts max. Out at sea in Lyme Bay you will be hard pushed to find 2kts of tide. Usually 0.5 to 1.5 on most tides. Dicky 1 Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted September 27, 2023 Author Share Posted September 27, 2023 23 hours ago, GPSguru said: Is your helm on the port side ? As you always should recover on the same side as the helm. With regard to the stern cleats, you can just take a single turn around anything on the stern as it is still the bow that is taking the strain. I take a single turn around the stern mooring cleat on the tube ! Yes, not leaving a good distance from bow to buoy is a common error. The closer it is, the smaller the arc that you tend to take, and therefore have less visibility and less control. my helm is on the starboard side and I recover from the port side. Recovering from the same side as the helm makes me now understand your earlier comment about making a 'very low speed skid turn' and also about looping the rode over the cleat which would work even with my cleats where they are 👍 Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted September 27, 2023 Author Share Posted September 27, 2023 4 hours ago, JonC said: Just a thought, when you next go to the boat have a look on the dashboard to see if you have one of these buttons, they really take the ball ache out of things. I've only got this one..... Geoff, Odyssey, Andy135 and 1 other 4 Quote Link to comment Share on other sites More sharing options...
Andy135 Posted September 27, 2023 Share Posted September 27, 2023 31 minutes ago, thejollysinker said: I've only got this one..... Quote Link to comment Share on other sites More sharing options...
GPSguru Posted September 27, 2023 Share Posted September 27, 2023 2 hours ago, thejollysinker said: my helm is on the starboard side and I recover from the port side. I know that some sea schools teach that method, but on most boats it has limited visibility to the warp and buoy position. BTW. You can always anchor with the buoy close to the boat (10m ish), and then let some warp out just before you recover. thejollysinker 1 Quote Link to comment Share on other sites More sharing options...
Odyssey Posted September 27, 2023 Share Posted September 27, 2023 I’d recommend a lazy line, If you’re running single handed and are worried about visibility use a bigger anchor ball, it’ll make it easier to see 🙂 only downside is bigger to store. if you ever lose sight of the ball/rode just stop. That way you can’t drive your boat over the rode 🙂 thejollysinker, GPSguru, Tamarisk64 and 1 other 2 2 Quote Link to comment Share on other sites More sharing options...
mike farrants Posted September 29, 2023 Share Posted September 29, 2023 I can usually see the buoy easy enough to chug past, if i cant then i try a touch of reverse before moving off to tighten the warp - this usually allows me to see the bouy one side or the other, then start my manoeuvre, but exactly as Ian says i tie off to a Samson post on the stern and pull from there - easy to see the warp. but the choppier the conditions the harder the manoeuvre is. some people put a small piece of broomstick or an alderny triangle thing between tbe bouy and boat to hold the bouy off a few meters thejollysinker and daio web 2 Quote Link to comment Share on other sites More sharing options...
thejollysinker Posted September 29, 2023 Author Share Posted September 29, 2023 8 minutes ago, mike farrants said: I can usually see the buoy easy enough to chug past, if i cant then i try a touch of reverse before moving off to tighten the warp - this usually allows me to see the bouy one side or the other, then start my manoeuvre, but exactly as Ian says i tie off to a Samson post on the stern and pull from there - easy to see the warp. but the choppier the conditions the harder the manoeuvre is. some people put a small piece of broomstick or an alderny triangle thing between tbe bouy and boat to hold the bouy off a few meters Cheers Mike. I have a triangle that Neil kindly donated and I was using it. Just needed to get even more space between boat and buoy and it was rough and I started flapping a bit 😅 Hopefully no more dramas thanks to all the good advice from everyone 👍😊 Andy135 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.