murray Posted June 4 Share Posted June 4 Hi everyone, I have a Ford 2711 E and would like to know the gearing between the engine drive shaft and the impeller used for cooling through the heat exchanger. I am having cooling issues and am wondering if there could be any slippage occurring between the 'motor' and the connection to the impeller pump. If anyone has an exploded diagram or can point me to one that would also be very helpful. I don't have a good photo of it but it is in the bottom left (out of sight) of the photo. Thanks in advance Murray Quote Link to comment Share on other sites More sharing options...
Andy135 Posted June 4 Share Posted June 4 Hi Murray, welcome aboard. When did the cooling issues first start, and did they come on suddenly or have they been getting worse gradually? What makes you suspect belt slippage or impeller not pumping? Could it be the heat exchanger has got salted/crusted up and isn't passing enough raw water through it to cool the engine? Quote Link to comment Share on other sites More sharing options...
Saintly Fish Posted June 5 Share Posted June 5 Hi Murray when was the raw water cooling impeller last changed? Have you removed it and inspected it? Have you checked all filters and other parts of cooling lines? Quote Link to comment Share on other sites More sharing options...
Gordmac Posted June 5 Share Posted June 5 There are two impellers, the one that pumps the seawater which draws from the sea through a stopcock via a strainer normally(is it clear?) then through various heat exchangers before exiting via the exhaust. In the 6 cylinder Fords this is gear driven from memory, is yours driven by a belt? The other impeller is driven by the belt in your picture and pumps coolant round the engine and heat exchanger and is a closed system, same as a car, this system is normally reliable. When was your seawater impeller last changed? Does the seawater flow out the exhaust look reasonable? Last time I had an overheat (6 cylinder Ford) it was a faulty oil cooler, traced with the aid of a non contact thermometer. daio web 1 Quote Link to comment Share on other sites More sharing options...
daio web Posted June 5 Share Posted June 5 could also be faulty thermostat what makes you think it overheating bud i got one of those engines when was the last time it was serviced are you only just using it again after winter or have you only just purchased it Quote Link to comment Share on other sites More sharing options...
willyhookit Posted June 5 Share Posted June 5 looking at the pulley in the picture are you its turning lookes very rusty in the belt groove it should have a polished surface and the belt looks very low in the grove this will spin at a slower speed than a belt that is flush with the pulley daio web 1 Quote Link to comment Share on other sites More sharing options...
murray Posted June 8 Author Share Posted June 8 Hey guys thanks for your responses. I do now have a new water pump. (the new ones have a SS boss as opposed to the light weight one you see in the photo. Since writing my post, I have been able to find out that the impeller is driven by gearing from the drive shaft (helical). I don' think the thermostat id faulty as the water out the exhaust gets so hot you can't touch it. I have inspected the impeller and it looks fine bu the Jabsco service assistant has told me it is likely one of two things; a worn back plate or an impeller that has expanded and therefor would need replacing. There is a plug that should be fitted at the from of the impeller to stop wearing and fill and air gap in the assembly so that the vacuum in the impeller housing works better so I am going to replace the impeller and make sure the front plug is in place. cheers, Murray Andy135 1 Quote Link to comment Share on other sites More sharing options...
murray Posted June 8 Author Share Posted June 8 PS - I have cleaned out the heat exchanger as it was all crusted up from sea water so there are no blockages through the cooling water intake circuit. Andy135 and Saintly Fish 2 Quote Link to comment Share on other sites More sharing options...
Andy135 Posted June 8 Share Posted June 8 Good stuff. Sounds like you're making progress. Keep us updated 👍 Quote Link to comment Share on other sites More sharing options...
Andy135 Posted June 8 Share Posted June 8 Just a thought - have you checked both impellers? The belt-driven closed-circuit engine cooling one and the gear-driven raw water one? Both need to be in working order for the system to cool as it should. Quote Link to comment Share on other sites More sharing options...
murray Posted June 11 Author Share Posted June 11 Hi Andy, Yes I actually have a new engine water pump. Cheers, Murray Andy135 1 Quote Link to comment Share on other sites More sharing options...
suzook12 Posted June 12 Share Posted June 12 On 6/8/2024 at 8:27 AM, murray said: I don' think the thermostat id faulty as the water out the exhaust gets so hot you can't touch it. I'm not quite following this.... Surely the thermostat controls the water temp in the closed circuit? Water out of the exhaust being hot? How are you determining which is water temperature and which is exhaust gas temperature? To be fair, water dumped into an exhaust with gas temps of approx 650 degrees C post turbo, yeah, the water will be hot! If you are running a temp gauge and that says normal, then you are prob running at normal temp, if it says hot, and you can't fins a reason, then change the sensor. You can test the thermostat in a cup to make sure it opens and closes and that the bleed hole/bypass is not blocked which could cause air locks Quote Link to comment Share on other sites More sharing options...
Saintly Fish Posted June 12 Share Posted June 12 5 hours ago, suzook12 said: I'm not quite following this.... Surely the thermostat controls the water temp in the closed circuit? Water out of the exhaust being hot? How are you determining which is water temperature and which is exhaust gas temperature? To be fair, water dumped into an exhaust with gas temps of approx 650 degrees C post turbo, yeah, the water will be hot! If you are running a temp gauge and that says normal, then you are prob running at normal temp, if it says hot, and you can't fins a reason, then change the sensor. You can test the thermostat in a cup to make sure it opens and closes and that the bleed hole/bypass is not blocked which could cause air locks Damn Steve you beat me to it! Andy135 1 Quote Link to comment Share on other sites More sharing options...
suzook12 Posted June 13 Share Posted June 13 7 hours ago, Saintly Fish said: Damn Steve you beat me to it! Must have been your thoughts I picked up on...... Saintly Fish 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.